Recaulking a Shower, Tub or Sink: The Full Step-by-Step Guide

Removing old silicone, prepping the joint, laying a neat bead and keeping mold from coming back.

November 11, 2026

Caulk is the flexible seal in places where two surfaces meet and move slightly, such as where a tub meets the wall. Because it stays damp and can trap soap residue, mold often grows into it over time.

A careful recaulk can make a bathroom look years newer and protect the walls from water. Here's how to do it from start to finish, with tips that make the result last.

Step 1: Remove the old caulk

Cut along both edges of the old bead with a utility knife or caulk removal tool, holding the blade flat to avoid scratching the tub or tiles. Then pull or scrape out the strip. A plastic scraper helps with stubborn bits.

Take your time here. Any old caulk left behind can stop the new bead from bonding, and moldy remnants can show through later. Some people use a caulk remover product to soften leftovers; follow its label and ventilate the room.

Throw away the removed caulk right away rather than leaving it in the tub, where moldy pieces can spread spores and leave marks.

Step 2: Clean and kill remaining mold

Once the old caulk is gone, you may see dark stains in the joint. Clean them with a mildew remover suitable for the surface, wearing gloves with the fan running, then rinse well with clean water.

Finish by wiping the joint with rubbing alcohol or a similar residue-free cleaner, as many sealant manufacturers recommend, to remove soap film so the silicone can bond.

Step 3: Let the joint dry completely

This is the step people most often rush. Silicone laid over a damp joint can trap moisture and mold underneath. Leave the area to dry with the fan running, ideally overnight or longer.

For a tub, some tilers suggest filling it with water before caulking, so the tub sits at its lowest point while the caulk cures. Afterward, the bead won't be stretched as hard when the tub is full during a bath.

Step 4: Lay a fresh bead

Apply painter's tape on both sides of the joint, leaving a narrow gap for the caulk. Cut the tube nozzle at an angle, with a small opening to start. Run a steady, continuous bead along the joint.

Smooth it right away with a caulk tool or a fingertip dipped in soapy water, then remove the tape at an angle before the silicone skins over. The result should be a smooth, slightly concave line.

Step 5: Let it cure

Keep the area dry for the full cure time on the tube before using the shower or tub. Many silicone sealants list around a day, but some need longer, and cool or humid rooms can slow curing.

If you filled the tub with water before caulking, drain it only after the caulk has cured.

Keeping new caulk clean

Mold-resistant caulk helps, but it isn't mold-proof. Run the fan during and after showers, wipe the caulked joints dry and rinse away soap residue regularly.

If you see small dark spots starting, clean them early with a mildew remover. Spots that keep growing back from inside the bead are a sign it's time to recaulk again.

Frequently asked questions

Can I put new caulk over the old caulk?

It's not recommended. New silicone doesn't bond well to old silicone, and any mold underneath can keep spreading and show through. Remove the old bead completely first.

Should I use caulk or grout in shower corners?

Inside corners and changes of plane, such as where walls meet or where the tub meets tile, are commonly sealed with flexible caulk because those joints move slightly. Grout is used between tiles on flat surfaces.

How long does recaulking last?

It varies with ventilation, cleaning habits and product quality. Recaulk whenever the bead is moldy, cracked, peeling or pulling away from the surface.

Silicone or acrylic caulk for a bathroom?

Silicone is generally preferred in wet areas such as showers and tubs because it stays flexible and water-resistant. Acrylic caulk is easier to paint and clean up, but it's typically used in drier areas.

More guides